Categories
News

Transmission Vehicle (CAT )

Transmission Vehicle (PPC) – a device that is responsible for speed control while driving a car, using this mechanism, the machine can give back up. On many cars set 3, 4 or 5-speed manual gearbox or speed automatic gearbox. Samsung describes an additional similar source. Manual transmission, combined with the differential, is contained in the crankcase. Removing and installing transmission (CPT) is first Inside the engine compartment, and then set the car on a lift or pit. 1. To remove the gearbox (transmission) with engine, first disconnect the negative battery terminal. Get all the facts for a more clear viewpoint with LG Electronics.

Then remove the air filter, coolant reservoir, the cylinder drive clutch and hydraulic tube. Then unplug all cables and connectors remove the upper starter mounting bolt, remove the box transmission from the engine by removing the bolts. Then with the car, remove the wheel (as described in "Replacing the wheel") and Coir screens. 2. Further work is being done below the engine. Drain the oil from the gearbox (CAT), disconnect the axis, the exhaust pipe, unscrew the screws with which the gearbox is mounted to the engine. Once you have removed the gearbox (transmission) from the engine, inspect the clutch components.

Most often follows replace clutch elements with new ones. Inspect the basic units of the box, paying attention to the fact that the gears, shafts had no visible damage. 3. Making the replacement of defective or worn-out mechanisms that assemble box, while under all covers must install new gaskets and apply a skim the surface of a special sealer. 4. Caps that are installed on the box, and Wash dirt, degrease the mating surface, apply a sealer. When renting gear (CPR), use the jack, do not forget to put a wooden plate between it and the gearbox. Surgery to repair the internal mechanism of transmission (CPT) is very complex, it must comply with professionals, we consider only the major activities related to its operation. 5. Pay particular attention to the speedometer. It also must be inspected for mechanical damage, be sure to inspect the drive gear, which should not be chopped off, signs of wear, and if you want to install the speedometer on the gearbox. 6. When removing the gearbox (transmission) from the car one of the operations that you have to do – is the removal of its traverse. 7. To do this, first loosen the two bolts attaching crossbars to the bottom of a car, then disassemble the crossbeam. When viewed from the gearbox (PPC) Pay particular attention to bearings. They should not have traces of wear and have a tight fit in the working shafts. In no event should not push the clutch pedal at a time when you remove the gearbox (transmission) from your car.

Categories
News

Buses In St. Petersburg

How to choose a bus in St. Petersburg and the wheels on your car? There are a variety of views – from the factory instructions spelled out exactly where the permissible size of wheels, tires and wheels, finishing held view on a rotten neighbor "Eight", which may declare that, after installing the "watermelon" with a huge flight of his car "just flew." Let's look at the issue impartially. Where does in the original list of recommended instruction sizes of wheels and tires? And he takes out engineering calculations and are directly tied to the kinematics of the suspension vehicle. Is taken into account everything – load on transmission components, the characteristics of an acceptable comfort, the force on steering wheel, and. Etc.

And all this is reinforced by tests. For this reason you should not trust the outside views – any deviation from the instructions are always destructive, because it concerns not harmless "bloat" in the cabin, but the most basic – Manageability. And well, if non-standard wheels and tires will be disastrous for the car, not for you. Therefore, before you purchase tires and wheels in St. Petersburg, reread the instructions and decide on possible options.

In extreme case, in our online shop wheels and tires will help you to sellers – Consultants. Tire rims Petersburg at prices lower prices available in PoKolesam. Ru. Shall examine the possible options. The first – the minimum wheels and tires is acceptable for your car in this configuration. In this case, you can save, and in some cases and improve comfort by setting the bus on wheels with higher profile with a guarantee that they will not clinging to the arches and suspension components. This can be output if the car is operated on bad roads. Principal only just to check whether the fit of these tires and wheels it to your configuration, as many foreign cars size brake calipers vary depending on the installed engine. Situation may arise that disk diameter is simply not enough to accommodate the calipers. The second option – opposite extreme – maximum larger wheels and tires with a low profile. Sure, the aesthetics here on the heights – the car clearly would be a "respectable". But often at the expense of resources – both tires and disks. Penetrate the low-profile tires on bad roads – a pair of trivia. A victim can and drive – the curb, kick, and As a result, you get a new wheel. And the price, as you know, increases in proportion to the diameter. In addition, it may be that the reserve would not fit in allotted to her place and her place will have to pay "dokatke. Is also not the most practical solution, inimitably away from tire. The third option – the most simple. Use of such size wheels and tires that he was the most common for your model and configuration the car. In this case, probably will not have problems not with the choice of drives, not with the choice of tires. Moreover, we can say that the machine's behavior (comfort, handling, braking distance) would be best for the balance of all qualities.

Categories
News

Construction Machinery

Nowadays in Russia, despite a substantial recovery and development of a large number of industries, production of construction equipment leaves much to be desired. In Russia, now the demand for such technology is growing steadily, and Many producers can not provide the necessary quantity of equipment, which is why many organizations have to order machines abroad. Construction equipment company Komatsu, Samsung, including excavators and bulldozers, are more popular in comparison with the special equipment of domestic producers. Today in Russia has gained enormous popularity building special machinery from China. The prc operates a large number of companies production of such equipment, so customers need to carefully analyze the market in order not to accidentally buy a fake. Indeed, high-quality Chinese technique is performed only on plants State-owned, where it passes quality control. All Chinese production technology as trucks shaanxi, bulldozers, cranes, excavators and wheel loaders xcmg characterized by excellent quality, operational simplicity and reliability, which is why it is so popular. Improve long-invented – that's the main principle of which is selected hardworking Chinese.

For example, the famous truck man was an example of which was made universal dumper shaanxi. The undeniable advantage of these trucks is their cost-effective. Low price of trucks is due not bad build quality, and cheap labor force, which in China very much. It is essential that this technique is extremely environmentally friendly, since it corresponds to global standards Euro-3. Such a construction equipment highlights the fact that it conforms to all for customer characteristics – has high maneuverability, mobility and exceptional build quality.


Notice: ob_end_flush(): failed to send buffer of zlib output compression (0) in /home2/nebraska/public_html/software-innovators.com/wp-includes/functions.php on line 5349